Infineon Technologies AS5047U Rotary Position Sensor
Infineon Technologies AS5047U Rotary Position Sensor is a Hall-effect magnetic sensor using CMOS technology. The Hall sensors convert the magnetic field component perpendicular to the chip surface into a voltage. The AS5047U Sensor is designed to offer fast absolute angle measurement over a full 360° range. The 14-bit on-axis magnetic rotary position sensor features integrated Dynamic Angle Error Compensation (DAEC™) with near-zero latency at higher rotational speeds. To improve signal quality at lower rotational speeds, the Dynamic Filter System (DFS™) reduces transition noise. The robust design of the AS5047U Sensor suppresses the influence of any homogenous external stray magnetic field. A standard four-wire SPI serial interface with Cyclic Redundancy Check (CRC) protection allows a host microcontroller to read 14-bit absolute angle position data and program non-volatile settings without a dedicated programmer.
The AS5047U provides incremental movement data as a set of Actinic Blank Inspection (ABI) signals with a maximum resolution of 16,989 steps and 4096 pulses per revolution. The resolution of the ABI output can be programmed to 10- 14 bits. This device also includes a standard UVW commutation interface with programmable pole pairs (1 to 7), ideal for controlling Brushless DC (BLDC) motors. The absolute angle position is also provided as a Pulse Width Modulation (PWM) encoded output signal.
The single-die Infineon AS5047U Magnetic Rotary Position Sensor is offered in a 14-pin Thin Shrink Small Outline Package (TSSOP) and is Infineon green and RoHS compliant.
Features
- DAEC (Dynamic Angle Error Compensation)
- DFS (Dynamic Filter System)
- Magnetic stray field immunity
- SPI, ABI, UVW, and PWM independent output interfaces
- 14-bit resolution
- 2800rpm maximum speed
- 4mA maximum output current
- 35mT to 70mT operating point range
- Overvoltage protection
- 3.3V or 5.0V supply voltage
- -40°C to +125°C operating temperature range
- TSSOP-14 package type
- RoHS compliant and Green
Applications
- Factory automation
- Building automation
- Robotics
- PMSM (permanent magnet synchronous motor)
- Stepper motor closed loop
- Optical encoder replacement
Videos
Block Diagram
Pin Designations
Development Tools
ams OSRAM AS5x47U Adapter Board
Enables easy and fast evaluation of the AS5047U and AS5147U Magnetic Rotary Position Sensors.
ams OSRAM AS5x47U Motorboard
Simple PCB that is designed to adapt to standard size BLDC or stepper motors.
ams OSRAM AS5247U Adapter Board
A small PCB built for quick testing or evaluation of the AS5247U magnetic position sensor.
ams OSRAM AS5247U Socket Board
Used for programming of AS5247U magnetic rotary position sensors.
Related Sensors
ams OSRAM AS5x47U Position Sensors
Optimized to enable efficient operation of electric motors in power steering and braking systems.
ams OSRAM AS5047P 14-Bit Rotary Position Sensor
14-bit rotary position sensor for high speed (up to 28krpm) angle measurement over full 360º range.
ams OSRAM AS5047D & AS5147 Magnetic Rotary Position Sensors
High-resolution rotary position sensors for fast absolute angle measurement over 360 degrees.
ams OSRAM AS5270 Magnetic Angular Position Sensors
Dual-die, high-resolution available with an analog output interface or a digital output interface.
Socket Board
The Infineon AS5x47-TS_EK_SB Socket Board allows quick programming of the AS5047D and AS5147 Magnetic Rotary Position Sensors without soldering, thanks to its ZIF Open-Top-Socket for TSSOP packages. The AS5x47-TS_EK_SB Socket Board features a 5-pin dual-row connector for
connecting to the USB I&P Box, and a 10-pin dual-row connector for connecting to the SD4Y Production Programmer. An 8-pin header gives access to UVW, ABI, and GND signals. All passive components needed for proper operation are included on the Socket Board. Only a 5V power supply mode is possible.
USB I&P Box
The AS5x47U Adapter Board and AS5x47-TS_EK_SB Socket Board can be used with the optional USB I&P (Interface & Programmer) Box, which enables users to read out the sensor data, write a configuration, and permanently program a configuration.
SD4Y Programmer
Infineon SD4Y Programmer is designed for high-speed programming AS5x4x, AS5x3x, and AS514x Magnetic Position sensors. The SD4Y Programmer features a 20-pin connector that connects to the AS5x47U Adapter Board or AS5x47-TS_EK_SB Socket Board. A USB cable connects the Programmer to a PC, where a Graphic User Interface (GUI) is used to program the target device.
Related Solutions
ams OSRAM Magnetic Position Sensors
Fit for motor control and any tough position sensing applications in various fields.